when i apply the power
Page 1 of 1 • Share •
when i apply the power
ok when im crusing along and suddenly say if i want to put my foot down if i do it gradually not as in a slow gradual but a gradual power uptake its fine but say if i put the power on hard sometimes i get like a big jerking is this normal i dont hiink it is any ideas what it could be. how else could i put it by jerking its like put the power on and sometimes justs makes a jerk which pulles me back slightly hard to explain any one know of this problem?
thraps- Posts: 4
Join date: 2007-11-26
Re: when i apply the power
what boost are you running? what management etc?
_________________
i pass everything but the petrol station!!!

eer founder- Admin
- Posts: 63
Join date: 2007-11-22
Age: 26
Location: durham

Re: when i apply the power
hi mate my e1 has started doing that since i had a 3in exhaust
put on think it needs a remap
put on think it needs a remap

baggy- Posts: 10
Join date: 2007-11-22
Re: when i apply the power
you cant remap a standard eI-III ecu.
have you got a boost guage if so what does it read? does it feel like you have run into a brick wall?
if so it could be fuel cut due to boost problems especially after fitting an exhaust and or air filter.
have you got a boost guage if so what does it read? does it feel like you have run into a brick wall?
if so it could be fuel cut due to boost problems especially after fitting an exhaust and or air filter.

E3GSR- Posts: 30
Join date: 2007-11-22
Age: 44
Location: n wales
Re: when i apply the power
i was told it was the 4 onwards that could not be mapped not the I-III but surely you can put a chip in and map the chip?? as thats what my local jap tuner is planning with mine
_________________
i pass everything but the petrol station!!!

eer founder- Admin
- Posts: 63
Join date: 2007-11-22
Age: 26
Location: durham

Re: when i apply the power
I-IV you cant map but yes you are quite right you can chip them it just needs the old eprom removed and a socket soldering in the board in its place.
i have the chips and programmer here as well as the maps
but what you can do is change the early ecu for a later ecu and map that but its a lot of messing around with the wiring looms and not really for the basic diy'er.
i have the chips and programmer here as well as the maps
but what you can do is change the early ecu for a later ecu and map that but its a lot of messing around with the wiring looms and not really for the basic diy'er.

E3GSR- Posts: 30
Join date: 2007-11-22
Age: 44
Location: n wales
Re: when i apply the power
ohh ohh ohh i am very excited now neil
any chance of a chip for me?? very desperate for one
_________________
i pass everything but the petrol station!!!

eer founder- Admin
- Posts: 63
Join date: 2007-11-22
Age: 26
Location: durham

Re: when i apply the power
to be honest m8 to do it properly you would need to put it in the car road test it and use a datalogger then adjust the map and burn another chip and repeat the process.
it can be very time consuming.
it can be very time consuming.

E3GSR- Posts: 30
Join date: 2007-11-22
Age: 44
Location: n wales
Re: when i apply the power
_________________
i pass everything but the petrol station!!!

eer founder- Admin
- Posts: 63
Join date: 2007-11-22
Age: 26
Location: durham

Re: when i apply the power
or apexi power fc djet kit and commander 

E3GSR- Posts: 30
Join date: 2007-11-22
Age: 44
Location: n wales
Re: when i apply the power
can you do one of them chips they do on ebay mate?
_________________
i pass everything but the petrol station!!!

eer founder- Admin
- Posts: 63
Join date: 2007-11-22
Age: 26
Location: durham

Permissions of this forum:
You cannot reply to topics in this forum





